The Salt Lake Valley
We are Linked With Zello Through The
West Valley Network Channel
Our Repeater Covers The Salt Lake City Valley
JUST SO YOU KNOW WE ARE ON THE AIR SO PLEASE
RE FRAME YOURSELF FROM USING BAD LANGUAGE !!!
WQVJ267
WQVJ267 & 1/2
To join the channel.
Please use the contact form below on this website to
send me a message that you would like to join the group.
​
​
​
​
Listen Live
Click on speaker to UN-MUTE
​
Those without VoLTE ( 4G/LTE ) technology phones could lose mobile service in 2021
As we touched on earlier this year, the nationwide mobile providers will be shutting down their 2G and 3G networks to make way for new 5G networks. At that time, we noted that the shutdown process had already begun and 3G users could start experiencing service disruptions. It’s now become clear that those with older phones will need to upgrade to VoLTE phones as a matter of urgency since their phones will stop working
​
What you need to set up your own Network!!
#1 A Solidtronic or Radio Tone PC-Radio Interface Zello Gateway
Click Here For Solidtronic on Ebay
Click Here For Radio-Tone on Ebay
#2 A computer with Windows XP, or 7
Click Here For Computers on Ebay
#3 A QYT 980plus radio or HT or
Leixen VV-898s
for the Leixen vv898s are the same.
#4 A couple of Handhelds or A extra radio to be able to talk to the network.
That's all there is to a simplex network over Zello. Network must be setup on a separate antenna.
.jpeg)
.jpg)
Repeater Controller Cable For QYT WACCOM KT-UV980
Also fits Leixen VV-898s
SURECOM SR-629 Duplex Repeater Controller with QYT KT-UV980 for Mobile & HT Radio CABLE
What the Network Looks Like
Three Primary Modes of Amplfication
　
Radio Controlled
Connect to the antenna output of the handheld transceiver to the RF-IN connector on the rear panel of the amplifier with the Radio to Amplifier RF cable. Transmit and receive right on the Handheld radio - while your output signal is amplified
　　　
　
Accessory Controlled
Connect to the antenna output of the handheld transceiver to the RF-IN connector on the rear panel of the amplifier with the Radio to Amplifier RF cable. Connect a speaker microphone, headset, or compatible accessory to the radio. Transmit and receive right on the accessory connected to the Handheld radio - while your output signal is amplified.
　
　　　
　Amplifier Controlled
Connect the speaker microphone to the MIC jack on the front panel of the amplifier. Connect to the antenna output of the handheld transceiver to the RF IN connector on the rear panel of the amplifier with the Radio toAmplifier RF cable. Connect the accessory port of your radio to the Control jack on the front panel of the amplifier using the Amplifier Control Cable. Transmit and receive using the speaker microphone on the amplifier while incoming audio is relayed through the loud amplifier speaker.
Specifications:
　
Frequency range: 400-470MHz
Power supply: 13.8 VDC (± 15%), 5.5 A maximum
Input RF power: 2 - 6W (± 10%)
Output RF power: 20 - 40W
Size: 5.5 in D x 4.5 in. W x 1.4 in. H (135 mm D x 115 mm W x 36 mm H)
Dead weight: 1.5 lbs. (680 g)
.jpeg)
Feature:
â–¶ DMR and P25 Phase 2 modes
â–¶ Automatic switching
â–¶ VR-P25U is suitable for FDMA mode (C4FM, D-Star, NXDN, IDAS, dPMR, P25, MPT1327, etc.)
â–¶ High output power up to 40 watts with an input power of a handheld radio of 2-6 watts can be achieved up to 40 watts output power.
â–¶ UHF band: The amplifier VR-P25U / UD can support UHF (400-470MHz)
â–¶ small design at a size of 35 * 115 * 135cm it is particularly suitable for outdoor use such as Fielddays or for mounting in the car
â–¶ Certifications: All VGC amplifiers have been certified by CE, FCC.
â–¶ Multi-functional: Includes voltage stabilizer, overheating protection, RF sensing, auto power off, harmonic filters.
â–¶ Integrated speakers and microphone connection
â–¶ Status display about the current operating state
Tram 1477 Pre-Tuned
Antenna
.jpg)
Mobile Mag Mount Antenna
on Ebay
